So, this is it, back to our topic once again. Today, i would like to share to you some tips on setting up streamyx line. Hopefully it could be usefull for u, for me, and for all. Just follow the below step and ur back in line babeh..
Setting up Modems for Streamyx Tips:
1 DSL Technologies
1.1 ADSL
Asymmetric Digital Subscriber Line
ITU G.992.1 - G.DMT - 8.0Mbit/s, 1.0Mbit/s
ITU G.992.2 - G.Lite - 1.5Mbit/s, 0.5Mbit/s
ITU G.992.3/4 - ADSL2 - 12Mbit/s, 1.0Mbit/s
ITU G.992.5 - ADSL2+ - 24Mbit/s, 1.0Mbit/s
1.2 SDSL
Symmetric Digital Subscriber Line
1.3 SHDSL
Symmetric high-speed digital subscriber line
ITU G.991
1.4 VDSL
Very high bit-rate Digital Subscriber Line
ITU G.993.1 - VDSL
ITU-T G.993.2 - VDSL2
2 Signal Level Guide
2.1 ADSL
Downstream SNR = 15 dB.
Higher is better, minimum = 6 dB.
Downstream Power = < 15 dBm.
Lower is better.
Upstream SNR = 10 dB.
Higher is better.
Upstream Power = < 15 dBm.
Lower is better.
Downstream Attenuation = < 30 dB
Lower is better, maximum = 60 dB.
Upstream Attenuation = < 30 dB
Lower is better, maximum = 60 dB.
2.2 ADSL2+
Downstream SNR = 06 dB.
Higher is not better, within range is better = 05 - 07 dB.
Downstream Power = < xx dBm.
Lower is better.
Upstream SNR = 06 dB.
Higher is not better, within range is better = 05 - 07 dB.
Upstream Power = < xx dBm.
Lower is better.
Downstream Attenuation = < 22 dB
Lower is better, maximum = 22 dB (for 10mbps), 12 dB (for ~25mbps).
Upstream Attenuation = < 22 dB
Lower is better, maximum = 22 dB (for 10mbps), 12 dB (for ~25mbps).
3 VPI/VCI ( IMPORTANT ) - Failing to adhere modem won't dial
For Streamyx, VPI = 0 , VCI = 35
Belkin Modems = VPI = 0 , VCI = 35 ( defaults at VPI = 0 , VCI = 38 )
Thomson Modems VPI/VCI = 0.35 ( default at 8.35 )
Username : abc@streamyx ( replace abc with your username )
Password : xxxx ( replace xxx with your password )
CASE STUDIES :
DSL Status: UP
DSL Modulation Mode: GDMT
DSL Path Mode: FAST
Downstream Rate: 1024 Kbps
Upstream Rate: 512 Kbps
Downstream Margin: 22 db <-- 13yrs="13yrs" line="line" old="old" p="p" telephone="telephone">Upstream Margin: 8 db
Downstream Line Attenuation: 54
Upstream Line Attenuation: 31
Downstream Transmit Power: 0
Upstream Transmit Power: 0
PVC Connection
Connection: 1
Encapsulation: RFC 2516 PPPoE
Multiplexing: llc
Qos: UBR
Pcr Rate: 0
Scr Rate: 0
Autodetect: Disable
VPI: 0
VCI: 35
Enable: Yes
PVC Status: Applied -- OK
Solution : Now the DS Margin is 22dB and you're able to get 1024 / 512.. old telephone cables do give problems if they deteriorate too badly.. check and see if the cables connecting to the socket/ junction box that you plug your phone line in, are they black in color due to being struck by lightning often ? If they are, try to cut off the carbonised section and connect back using the section which is in good condition.
